Error reported but no error

  • Resolved AdrianoAgri

    (@adrianoagri)


    8 years, 2 months ago

    Hi.
    I have installed the plugin onto a multisite, in the main site everything goes well,
    in the child site, everything seems goes well but some error in the ssl admin panel
    “Fixer mixed content is enabled, but was not detected on the first page”
    “The https redirection has been set in javascript, because you’ve enabled WordPress Multisite for a site in a subfolder. Install networkwide to set the redirect in .htaccess.”

    These are two alert in the admin panel, but in the frontpage everythings seems going well. i have checked for the fixer but i haven’t find it.
    I have also checked for network activation but no ssl admin panel in the network admin for networkwide installation.

    In the child site, i have inspect home page and looked into the console tab. The only message i found were three error 404 for css and js of woo extra fee plugin.

    I could have some kind of problem in the child site?

    thanks
    Adriano

Viewing 7 replies - 1 through 7 (of 7 total)
  • Plugin Author Rogier Lankhorst

    (@rogierlankhorst)

    Network activation can be done in the network admin of your multisite, on the plugins overview. Network activate the plugin, then choose, activate network wide. It’s possible you need to deactivate it first, then reactivate.

    Thread Starter AdrianoAgri

    (@adrianoagri)

    Hi. i read only now,
    the plugin says active on network, but i cannot deactivate it in any way.
    I have seen that in the property of the plugin, is checked allow javascript to manage ssl redirecting.

    How can i deactivate the plugin? to force network activation?
    thanks

    Plugin Author Rogier Lankhorst

    (@rogierlankhorst)

    Did you activate the plugin networkwide on WP plugins page of the network admin?

    Thread Starter AdrianoAgri

    (@adrianoagri)

    It results activated, but when i have installed the plugin, i have activated only in one site because i need ssl only in one page in the main site.
    After that i have noticed some errors, and reading here and there on this support forum i understood that it should be better to have the entire site under ssl, and because navigating i had alert from google on mixed content. so i have activated the plugin also in the second site, it said that the plugin was already active, has done some operations, and then says everythings was ok..
    only in the backend of both of sites remain the message to install networkwide for htacces managment.
    So last time, i have tried to deactivate form network admin panel but nothing happens, i have tried to deactivate from the single site, but it says that the plugin is under network activation.

    I don’t know if you can get me, my english could not be very clear…
    thanks..

    Plugin Author Rogier Lankhorst

    (@rogierlankhorst)

    If everything works fine, you can also dismiss these notices by clicking the x in the right top of the notice.

    Thread Starter AdrianoAgri

    (@adrianoagri)

    Yas i have dismiss the notice but i notice that after a while the message appears again, (i have dismiss again),and, i don’t know if depends on ssl, but i have noted that i have some difficult on redirecting to the admin dasboard in the second site, the one which i have activated ssl after some days after the first activation…
    And consider that in the ssl admin panel i still have the message for the network activation…
    I only wish to know if that can cause problems, and just because some errors occours (like accessing the second site admin dasboard, or the same loggin in in the same admin dashboard).

    thanks

    Plugin Author Rogier Lankhorst

    (@rogierlankhorst)

    This causes no problems. I’ll investigate to see what can cause these notices, and hope to have improved this in the next release.

Viewing 7 replies - 1 through 7 (of 7 total)
  • The topic ‘Error reported but no error’ is closed to new replies.